Versachem Heavy Duty Tailpipe Repair Kit

US Item #: 10342
CA Item #: 10342
Tech Docs
Tech Docs
Product Details:
VersaChem’s Heavy Duty Tail Pipe Repair Kit withstands extreme temperatures up to 2000⁰F. This permanent repair solution includes a metal wire screen and exhaust clamp that seals 2X larger holes and leaks compared to traditional kits. 

Units per case: 6

Features
1Temperature resistant up to 2000°F
2Seals 2X larger holes and leaks with a strong and long-lasting seal 
3Epoxy resin infused bandage – 2” x 42” (84 sq in)
4Seals out exhaust gases
5Seals exhaust system cracks and holes
6Includes metal wire screen and exhaust clamp for permanent seal 
7Fits pipes 1-1/2” to 2-3/4”
Tailpipe
DO NOT APPLY WHILE MOTOR IS RUNNING.

STEP 1: Using sandpaper, smooth area around hole. To clean, rub the buffered area with the provided alcohol wipe.

STEP 2A: Squeeze generous amount of putty and completely cover the crack or hole using putty spreader. Let sit for 30-45 minutes. (Speed up drying time with heat gun or hair dryer.)

STEP 2B (for holes greater than ¼”): 1. Cut reinforcing wire screen to appropriate size to cover the hole. Apply small amount of putty with putty spreader around hole to secure wire screen in place. 2. Squeeze generous amount of putty and completely cover the wire screen using the putty spreader. Let sit for 30-45 minutes. (Speed up drying time with heat gun or hair dryer).

STEP 3: Remove red backing on BOTH sides of clear bandage.

STEP 4: Wrap complete bandage around repair area, overlapping edges at least ½”. Overlapping edge by 1” provides extra
protection if needed. Note: Overlap the wrap as many times as possible, making sure at least 3 wraps are over the damaged area.

STEP 5: Support bandage with metal strapping. Using screwdriver, tighten bolt to secure metal clamp. DO NOT OVERTIGHTEN.

STEP 6: Let repair set and cure overnight. For faster return to service, let vehicle ideal for 20-30 minutes. Temperature resistant bandage seals itself with heat from vehicles’ exhaust.

WARNING STATEMENT Causes serious eye irritation. Causes skin irritation. May cause an allergic
skin reaction Contains: Fiberglass yarn, Bisphenol A, Methyl ethyl ketone, Kaolin, Acrylic acid polymers, Carbon black. Use immediately after opening.
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Use personal protective equipment as required.
Wash face, hands and any exposed skin thoroughly after handling. Wear protective gloves/protective clothing/eye protection/face protection. Avoid breathing
dust/fume/gas//mist/vapors spray. Contaminated work clothing should not be allowed out of the workplace. IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. IF ON SKIN: Wash with plenty
of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. Store in a well-ventilated
place. Keep container tightly closed. Store locked up. Dispose of contents/container to an approved waste disposal plant. Keep out of the reach of children.
WARNING: Cancer – www.P65Warnings.ca.gov

You may also like...

10343 Muffler Repair Kit
Muffler Repair Kit
favicon 512x512 1
Mega Grey™ Silicone
99939 VC Mega Grey RTV
Mega Grey™ Silicone
99839 VC Mega Black RTV
Mega Black™ Silicone
90214 mockup
Plastic Tank & Radiator Repair Kit
90180 mockup
Heavy-Duty Fuel Tank Repair Kit
Buy online